Usage rules of ammeter from Kunshan ammeter manufacturer:

① The ammeter should be connected in series with the electric appliance in the circuit (otherwise, the ammeter will be burnt due to short circuit)

② The current should come in from the "+" terminal and come out from the "-" terminal (otherwise, the pointer will be reversed and the needle will be bent easily.)

金彩汇③ The current to be measured should not exceed the range of the ammeter (you can try to touch it to see if it exceeds the range.)

金彩汇④ It must not be allowed to connect the ammeter to the two poles of the power supply without using electrical appliances (the internal resistance of the ammeter is very small, equivalent to a wire). If the ammeter is connected to the two poles of the power supply, the pointer will be crooked, or the ammeter, power supply and wire will be burned.)

金彩汇Note: first burn the ammeter, then destroy the source

金彩汇How to use ammeter

金彩汇1. Adjust the zero button with a flat screwdriver.

2. Selection of measuring range (estimated by experience or by touch test)

Ammeter comes down to three views and three questions to see the range of ammeter first, generally on the dial marked. After confirming one of the cells indicates how many amps connect the positive and negative terminals of the ammeter into the circuit, observe the position of the pointer and then read. In addition, the ammeter with the appropriate range should be selected. You can try to touch it first. If the pointer does not swing obviously, change the meter with small range. If the pointer swings at a large angle, change the table for a large range. The general pointer is around the middle of the dial, and the reading is more appropriate.

One look: range, ammeter measurement range.

Second, the index value, a small cell of the dial represents how much.

金彩汇Three: pointer position, the position of the pointer contains how many index values.

金彩汇Ammeter reading

金彩汇1. See the range

金彩汇2. See the index value clearly (generally speaking, the scale 0-3A index value is 0.1A and 0-0.6a is 0.02A)

3. See the stay position of the probe (always observe from the front)

金彩汇Preparation before use:

1. Adjust the zero button with the flat tap.

2. Range (estimated by experience or touch test method)

金彩汇The use method of ammeter

1. Connection table

Ammeter must be connected in series in the circuit to be tested, so that the current flows from the "+" terminal of ammeter and out of the "-" terminal. When using ammeter, its two terminals must not be directly connected to the two poles of the power supply, otherwise, the ammeter will be burnt out due to excessive current.

金彩汇2. Select the range of the table

The ammeter has three terminals, as shown in the figure above. If the ammeter is connected to the two terminals of "+" and "0.6", its range is 0.6A, and read the group of values on and below the dial; If connected to the terminals "+" and "3", the range is 3a, and the set of values on the dial is read. Before the experiment, if we don't know how to connect, we can estimate the current value in the circuit first. If the estimated current is less than 0.6A, the range should be selected. If the estimated current is greater than 0.6A, but less than 3a, the range should be selected. If it is not estimated, it can be carried out by touch test (fixing one terminal and using another terminal of circuit to quickly measure the terminal), and then selecting the appropriate range according to the deflection angle of ammeter pointer.

3. Test circuit

After the physical drawing is connected according to the circuit diagram, the test connection must be carried out. Carefully observe the deflection of ammeter pointer during test connection. If the pointer does not deflect, it means that there is an open circuit somewhere in the circuit; If the pointer deflects in the opposite direction, it indicates that the positive and negative terminals of the table are connected reversely; If the angle of pointer deflection is too large, the range is selected to be small; If the angle of pointer deflection is too small, the range is too large. Then according to the observed situation during the test, the relevant experiments are carried out after the corresponding adjustment.